D-link dwl-2100ap setup

Authentication For added security on a wireless network, data encryption can be enabled. There are six available Authentication type can be selected. The default value for Authentication is set to "Open System". Open System For Open System authentication, only the wireless clients with the same WEP key will be able to communicate on the wireless network. The Access Point will remain visible to all devices on the network.

Shared key For Shared Key authentication, the Access Point cannot be seen on the wireless network except to the wireless clients that share the same WEP key. Stations have the option of using either but must still have the correct key to decrypt data.

WPA uses stronger security than WEP and is based on a key that changes automatically at a regular interval. It uses TKIP encryption to protect the network through the use of a pre-shared key. Also referred as private settings. The default IP address is IP address The default IP address is It can be modified to conform to an existing local area network.

Getting Started Using the Configuration Menu Using the AP Manager. Networking Basics Technical Specifications Note: Using a power supply with a different voltage rating than the one included with the DWLAP will cause damage and void the warranty for this product.

With the DWLAP, bandwidth-intensive applications like graphics or multimedia will benefit significantly because large files are able to move across the network quickly. The DWLAP is capable of operating in one of 5 different modes to meet your wireless networking needs.

The DWLAP can operate as an access point, access point-to-multi-point bridging mode with AP function, access point-to-multi-point bridging mode without ap function, repeater, or wireless client mode. The DWLAP is an ideal solution for quickly creating and extending a wireless local area network WLAN in offices or other workplaces, trade shows and special events.

The When used with other Wi-Fi Protected Access which authorizes and identifies users based. You only need to input your encryption information once in the configuration menu. No longer will you have to manually input a new WEP key frequently to ensure security. With the DWLAP, you will automatically receive a new key every time you connect, vastly increasing the safety of your communication.

Actual data throughput will vary. Network conditions and environmental factors lower actual data throughput rate. LAN: Blinking green light indicates activity on the Ethernet Port; solid green light indicates connection.

WLAN: Blinking green light indicates wireless activity; solid green light indicates connection. Superior wireless. A D-Link D-. View module will be downloadable for network administration and real-time network traffic monitoring with D-Link D-View software. D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks.

D-Link wireless products will allow you access to the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking brings. WLANs are used increasingly in both home and office environments, and public areas such as airports, coffee shops and universities. Innovative ways to utilize WLAN technology are helping people to work and communicate more efficiently. Increased mobility and the absence of cabling and.

Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop and desktop systems support the same protocols as. Mobility - Productivity increases when people have access to data in any location within the operating range of the WLAN. Management decisions based on real-time information can significantly improve worker efficiency. Networks that frequently change can benefit from WLANs ease of implementation. WLANs can operate in locations where installation of wiring may be impractical.

Installation and Network Expansion - Installing a WLAN system can be fast and easy and can eliminate the need to pull cable through walls and ceilings. Wireless technology allows the network to go where wires cannot go - even outside the home or office. Inexpensive Solution - Wireless network devices are as competitively priced as conventional Ethernet network devices.

Scalability - WLANs can be configured in a variety of ways to meet the needs of specific applications and installations. Configurations are easily changed and range from Peer-to-Peer networks suitable for a small number of users to larger Infrastructure networks to accommodate hundreds or thousands of users, depending on the number. The IEEE It increases the data rate up to 54 Mbps Mbps in Super G mode within the 2.

This means that in most environments, within the specified range of this device, you will be able to transfer large files quickly or even watch a movie in MPEG format over your network without noticeable delays.

M ultiplexing technology. OFDM works by splitting the radio signal into multiple smaller sub-signals that are then transmitted simultaneously at different frequencies to the receiver. OFDM reduces the amount of crosstalk interference in signal transmissions. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range.

Typical ranges vary depending on the types of materials and background RF radio frequency noise in your home or business. The key to maximizing wireless range is to follow these basic guidelines:. Position your devices so that the number of walls or ceilings is minimized.

A wall that is 1. At a 2-degree angle it looks over 42 feet 14 meters thick! Position devices so that the signal will travel straight through a wall or ceiling instead of at an angle for better reception.

Try to position wireless devices and computerswithwirelessadapterssothatthesignalpassesthroughdrywalloropen doorways and not other materials. An Infrastructure network contains an access point or a wireless router.

The Infrastructure Network example shown on the following page contains the following. D-Link network devices your existing network may be comprised of other devices :. Please remember that D-Link Air Plus Xtreme TM G wireless devices are pre-configured to connect together, right out of the box, with their default settings. Consult with your Cable or DSL provider for proper installation of the modem. Type admin in the User Name field. Please refer to the.

Quick Installation Guide for more information regarding the Setup Wizard. Enabling this feature broadcasts the. All devices on the network must share the same.

Super G Mode- Super G is a group of performance enhancement features that increase end user application throughput in an Super G is backward compatible to standard For top performance, all wireless devices on the network should be Super G capable. Disabled: Standard Compression, and Dynamic Turbo mode. This setting is backwards compatible with non-Turbo legacy devices. Dynamic Turbo mode is only enabled when all devices on the wireless network are configured with Super G with Dynamic Turbo enabled.

Select Enable or Disable , Disable is selected by default. WMM stands. Select Open System to communicate the key across the network. Select Shared Key to limit communication to only those devices that share the same. Select Disabled or Enabled.

Disabled is selected here. Select , , bits. Select the 1st through the 4th key to be the active key. Input up to four keys for encryption. You will select one of these keys in the valid key field. Group Key Select the interval during which the group key will be valid. Update Interval- is the recommended value. Alower interval may reduce data transfer rate.

Radius Port- Enter the Radius port. Select the interval during which the group key wll be valid. The default value of is recommended.

Group Key Select the interval during which the group key wll be valid. Update Interval: default value of is recommended. PassPhrase: Enter a PassPhrase in the corresponding field.

This is considered your internal network. These settings may be referred to as private settings.