Xfinity remote setup 991

If the code is accepted, the green light will flash twice. If it flashes red twice, try entering the code again. Press the Power button on your Xfinity remote to test. If pressing the button turns off your TV, you've successfully programmed your TV into the remote.

If your TV remains on while the Xfinity box turns off, you should try another programming code. To do that, press and hold the Setup or Set button again and then enter the code. If you want to use your remote to control other components, press the power button again to turn the TV back on and keep reading. Program other components. Press and hold the Setup or Set button until the light turns green or flashes red, if you're using an older black remote. Enter the code for the component.

As long as the code is accepted, the status LED should blink green twice again. If not, try one of the other codes. Repeat for each component you want to control. Method 5. Try programming your remote control with another method first. If you were unable to make your Xfinity remote control work to power your TV on and off, it's likely that there's an issue with the code s. This method should be a last resort, as you'll have to cycle through tons of codes until the right one is found.

If you've run out of codes to enter, you can use this method to scan for the TV code. This method will not work for the XR16 or XR15 remotes. Press and hold the Setup or Set button on your remote. Continue holding down for about five seconds. You can lift your finger when the light at the top turns green. If you're using the older black component remote with a red button at the top-right corner, your light will never turn green.

Lift your finger when it blinks red twice. Use the number pad to enter The indicator light will flash green two times. Press the "Channel Up" button repeatedly until your television powers off. This cycles through the entire list of codes, so it can take a long time. Once you arrive to the right code, your TV will turn off. Press Setup or Set button on the road to save the code. You can then press the Power button to turn the TV back on.

When the TV comes back on, your remote will be programmed to use with your TV. Method 6. Make sure everything is plugged in securely and can power on manually. This can help rule out hardware problems with your television or audio device. Turn everything off and start from scratch. If your remote is doing weird things like turning your X1 box off and while turning the TV on, power down all of your components using their own power buttons.

Then, press the All On' or Power button to turn everything on together. Replace the batteries if your remote is unresponsive. In some cases, low battery life can interfere and cause problems with programming. Furniture and other large objects can interfere with the signal and prevent you from being able to successfully program your remote.

Contact Xfinity customer support if you are unable to program the Xfinity remote with your television or audio device. Xfinity may be able to resolve problems with your remote or replace the remote entirely. Check the remote control for a button or switch that will let you change the remote setting to "cable. You may have to set up the remote to control your specific cable box, which would be covered in the directions. Not Helpful 0 Helpful 2.

Include your email address to get a message when this question is answered. If you program your Xfinity remote control to work with your soundbar, you will not be able to use it to control your TV's volume separately. Helpful 0 Not Helpful 0. Check out Xfinity's voice command tip guide to learn about all of the things you can do with your voice remote.

You Might Also Like How to. How to. About This Article. Written by:. Nicole Levine, MFA. Co-authors: 3. Updated: January 12, Once the on-screen pairing code is correctly entered, your remote is paired with the TV Box. Note: If you do not see on-screen pairing instructions after pressing the xfinity button in step four, press the xfinity button again. You may need to press the xfinity button multiple times if there is more than one TV Box in range.

Press and hold the xfinity and Info buttons for five seconds. Once the TV turns off, press Setup to lock in the code. Press the TV power button on the remote. If the TV turns on, you're all set! Press and hold the xfinity and Mute buttons together for five seconds until the light at the top changes from red to green. Type the first five-digit code for the TV manufacturer. If the remote light blinks green twice, the code is correct.

If the remote light blinks red then green, the code is incorrect. Aim the remote at the TV, and press the Power button. If the TV doesn't turn off, try the next code. Activate the remote by removing the pull tab on the back. Follow the on-screen instructions that come up on your TV to finish setup.